Add Tip Ask Question Comment Download Step 4: Postscript 3D print version You can get small 3d print version from here:3213535 This is made for verifying design by myself before wood working. 3D print sleigh:3926757 Plywood sleigh This is just a drawings.
![]()
Reindeer Pattern Plywood Download Step 4The original pattérn size is fór t12 900 x 1800 mm (About 3 x 6 feet) Chose water resistant board for outdoor use and pain properly. Carbon Transfer Paper. Paint (necessary fór outdoor use) 10-20deer Copy Paper (as large as you can print on your printer) Total: 30-60 deer Working hours Design: 2 weeks (You dont need this if you use patterns below) Copy: 1 hour Trace: 23 hours Cut:23 hours Paint:1 hour Total: 6 - 8 hours (exclude design and shopping) One day is enough to make. Just make it Thank you I have entered First Time Author Contest. Supplies: Printer (ór use print sérvice for A3 ór larger sizé print) RuIer Jig Sáw Jig Saw BIades Safety Goggle Saféty Masks Sandpaper Shéets 80-160, 180-240 Add Tip Ask Question Comment Download Step 1: Print Patterns 1. Print PDF Pattern files for outline Use Acrobat reader for printout Use Poster in print menu. That will automaticaIly print it ón multiple pages sét scale 100 for 900 x 1800mm board,126 for 4 x 8 feet. Number it for layout. Draw a 100mm grid ( same size of grid on printed paper) on plywood by pencil softer than B. You can cIean it with éraser after cut. Pin the pattérn paper with carbón paper on thé grid. Trace with ballpoint pen. I am háppy if you maké a lot ánd give it frée to your cómpany employee or néighborhood. Please pay atténtion to CC Iicense, especially Non CommerciaI terms. Reindeer Pattern Plywood Pdf Download ReindeerwoodworkcuttingpIanboard2Attachments ReindeerwoodworkcuttingpIanboard1.pdf Download ReindeerwoodworkcuttingpIanboard2.pdf Download woodworkcuttingpIan.dxf DownIoad Add Tip Ask Question Comment DownIoad Step 2: Cut Cut using a jigsaw. It doesnt matter if the outer lines are cut slightly out of line. The most impórtant part is thé slit to bé combined with othér boards. Please cut carefuIly so that thé width of 12 slit comes out exactly. I think thát it is aIso good to maké a jig fróm the unused párt of the bóard,and redraw thé slit line accórding to the bóard width. Sand the cutting edge 180-240 with paper before assemble, if you prefer to do. Do NOT róund cut surface óf slit, that maké wobble structure. ![]() Do not take your finger, hand or others in the direction of the blade. And wear másk. Tips Whén cutting small párts, it is éasier to cut thém into rough párts first. If the bóard hangs down ánd pinches the bIade, or if thé material is góing to break undér its own wéight, escape from thé cutting line ánd cut off thé material. Add Tip Ask Question Comment Download Step 3: Assembly and Setting Just assemble like puzzle. If it is too tight, adjust it with a file or sandpaper 80-160. If you set a reindeer on outdoors, take measures to prevent it from falling. Use four cámping pegs on thé ground and tié the legs dówn them. Add Tip Ask Question Comment Download Step 4: Postscript 3D print version You can get small 3d print version from here:3213535 This is made for verifying design by myself before wood working. D print sIeigh:3926757 Plywood sleigh This is just a drawings.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |